KAD/ADC/117/EC1 8 channel Full-bridge ADC
- REQUEST A QUOTE
- Eight full bridge or differential ended input channels
- Programmable input range (±10mV to ±10V)
- High accuracy (0.08% FSR typical)
- Programmable current excitation per channel
- Short on any channel does not affect others
- 16-bit simultaneous sampling on each channel
- Two filtering mode: IIR and FIR
- Linear bridge operation – constant current
- Up to 24K samples per second per channel
- Up to 6kHz Bandwidth (AAAF filter)
- Analog signal Acquisition
- Differential Ended
- Full Bridge
- Half Bridge
Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...
The KAD/ADC/135 is used to condition and digitize up to 12 differential ended analog channels using simultaneous sampling 16-bit A/D for each channel. At the heart of the KAD/ADC/135 is a...
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
The NET/SWI/101 is an 8-port airborne Ethernet switch designed for operating in harsh environments. Each port is configurable for 10BaseT, 100BaseTX, and 1000BaseT link speeds or auto-negotiate...
8 channel, Full-bridge ADC (current excitation, programmable analog gain, configurable FIR/IIR filter, 3.75kHz b/w) - 8ch at 24ksps
The KAD/ADC/117/EC1 has eight channels of signal conditioning and data acquisition for differential voltages, strain gage and bridge measurements. In addition to the measurement channel, the KAD/ADC/117/EC1 provides independent constant current excitation for up to eight channels. Each differential ended signal has a separate programmable amplifier, filter and A/D converter.
At the heart of the KAD/ADC/117/EC1 is a hard-wired state-machine that over-samples all channels and digitally filters any noise above the user-programmable cutoff frequency. This is achieved using cascaded, half-band, decimate by 2, 15 tap, Finite-Impulse-Response (FIR) filters with 32-bit coefficients followed by an 8th order Butterworth (IIR) filter with a default cutoff point set to 25% of the sampling frequency. The IIR filter is bypassed in FIR mode with samples output directly from the FIR filter. All signals are sampled simultaneously. Thus, when several channels are sampled at different sampling rates, at least at the start of an acquisition cycle all channels will be aligned.
The excitation current is programmable (0 mA to 20 mA in 5 µA steps) and is kept constant. As the resistance changes, the voltage across the bridge (and hence as seen by the amplifier) changes linearly.
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.